Tenon® 100% Silane Sealer
Tenon® 100% Silane Sealer is a clear, solvent-based, concrete sealer that penetrates deep into, and reacts chemically, within the capillaries of the concrete or masonry in order to protect against moisture penetration and the spalling, freeze damage, and rebar corrosion which moisture can cause. It is suitable for use to protect and seal fully-cured fresh concrete, cast in place, precast, and high strength concrete materials. 100% Silane Sealer is used for above-grade exterior applications that are not subject to hydrostatic pressure. It is excellent for treating high traffic areas or surfaces that receive high salt concentrations such as coastal piers. Available in 1 gal. bottle (BOM #129890), 5 gal. pail (BOM #129900) and 55 gal. drum (BOM #129652).
Tenon® 20% Silane Sealer
Tenon® 20% Silane Sealer is a clear, solvent-based concrete sealer that penetrates deep into and reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and the spalling, freeze damage, and rebar corrosion which moisture can cause. It is suitable for use to protect, and seal fully-cured, new concrete, existing concrete, stucco, architectural concrete, and other cementitious materials. Silane sealers are used for above-grade exterior applications that are not subject to hydrostatic pressure. Available in 1 gal. bottle (BOM #129980), 5 gal. pail (BOM #129970) and 55 gal. drum (BOM #129644).
Tenon® 40% Silane Sealer
Tenon® 40% Silane Sealer is a clear, solvent-based concrete sealer that penetrates deep into and reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and the spalling, freeze damage, and rebar corrosion which moisture can cause. It is suitable for use to protect, and seal fully-cured fresh concrete, existing concrete, stucco, architectural concrete, and other cementitious materials. 40% Silane Sealer is used for above-grade exterior applications that are not subject to hydrostatic pressure. Available in 1 gal. bottle (BOM #129870), 5 gal. pail (BOM #129860) and 55 gal. drum (BOM #129597).
Tenon® Concrete & Masonry Sealer WB
Tenon® Concrete & Masonry Sealer WB is a water-based sealer that penetrates and reacts chemically within the capillaries of the concrete or masonry, bonding to the silica in the substrate to protect against moisture penetration, water-related staining, atmospheric chemicals, and deterioration. It is used to protect and seal clean, dry, coating-free, fully-cured concrete, brick masonry, concrete masonry units, stucco, stone terrazzo, architectural concrete, and some natural stones. For above-grade exterior applications that are not subject to hydrostatic pressure. Ready-to-use, this low VOC, silane/siloxane emulsion is especially suited for applications where VOC regulations for AIM coatings prevent the use of solvent-borne products. Available in 1 gallon bottles (BOM #120673) and 5 gallon pails (BOM #120674).
Tenon® Paver Seal Ultra Shine
Tenon® Paver Seal Ultra Shine is a high-solids, low-viscosity, sprayable sealing agent designed to protect & extend the life of installed pavers, while enhancing color and adding a high-gloss “wet look” finish. Made with a blend of 100% methacrylate polymers, this solvent-based coating does not yellow when exposed to the sun’s UV rays and can also be used as a final sealer on architectural concrete, brick, natural stone, and other cementitious materials. Paver Seal Ultra Shine will enhance the beauty and vibrancy of colored or stamped concrete and exposed aggregate giving it a rich high-gloss finish. It forms a membrane to increase protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these surfaces easier to clean. Available in 1 gal. bottle (BOM #129750), 5 gal. pail (BOM #129740), or 55 gal. drum (BOM #129556).
Tenon® Paver Wash
Tenon® Paver Wash is a mild, acidic product that dissolves and removes efflorescence (white mineral deposits) and rust stains from pavers and other cementitious or clay surfaces. This product is recommended to be used before applying a sealer to the surface of pavers in order to enables the sealer to penetrate and seal more effectively. Available in 1 gal. bottle (BOM #129800) or 5 gal. pail (BOM #129810).
Tenon® TraxGrip
Tenon® TraxGrip gives a light texture to concrete flatwork for a slip-resistant surface. Often used commercially on entrance floors, garage floors, steps, patios, walkways, and any surface where additional texture is desired to increase non-slip characteristics. TraxGrip is an optically clear thermoset polymer resin. Nearly invisible on the applied floor surface, it is added to curing and sealing compounds then applied to surfaces in the liquid solution. Available in 3.2 oz (BOM #120930) and 1 lb. (BOM #120927)