Tech-Mix® Portland-Limestone Cement is used to make concrete for a variety of building construction, repairs, stucco, or mortar applications such as sidewalks, floors, footings, patios, and setting posts, block, and brick. Tech-Mix Portland-Limestone Cement is available in 92.6 lb. bags (BOM #100908), 46.2 lb. bags (BOM #100910), and 2000 lb. bags (BOM #108140).
TechMix® Base Coat Stucco (BOM #112145) consists of a uniformly blended Portland cement-based dry mixture for use as the scratch and/or brown coat in a three-coat stucco application or the first coat in a two-coat application.
TechMix® Black Blast (BOM #106908) are abrasive blasting crystals that can be used for rust/paint removal and cleaning stone and brick. Additionally, the crystals hard, sharp, evenly-sized crystals make them ideal to frost/etch glass. Black Blast crystals work with all blasting equipment, are safe to use, and have a 1.5-2.0 mil anchor profile.
TechMix® Concrete Mix is a high strength pre-blended Portland cement mixture for pouring concrete 2 inches thick or greater. Used for general building and repairing steps, slabs, walks, and floors. Available in 60# bags (BOM #104879) and 80# bags (BOM #104883).
TechMix® Corefill Masonry Grout is formulated for superior flow to fill masonry voids while meeting ASTM C476 requirements for reinforced masonry construction. Corefill Masonry Grout is used to bond masonry units and steel reinforcement in the cores of the units together, as well as, filling reinforced bond beams. Available in 80# bags (Coarse - BOM #111227; Fine - BOM #111237) and 3000# bulk bags (Coarse - BOM #111120; Fine - BOM #111121).
TechMix® Crack-Resistant Concrete Mix (BOM #110260) is a high-strength, pre-blended Portland cement mixture for pouring concrete 2" (5 cm) thick or greater. Crack-Resistant Concrete Mix is air-entrained to increase freeze-thaw durability and fiber-reinforced to reduce shrinkage cracks and improve impact resistance. Meets or exceeds requirements of ASTM C387.
TechMix® Fast-Setting Concrete Mix (BOM #104877) is a specially formulated accelerated setting, high early strength mortar for use in applications of 2" thick or greater.
TechMix® Finish Coat Stucco (BOM #112146) is a uniformly preblended white Portland cement-based mix designed as the finish coat for traditional two and three-coat stucco applications. Produces a decorative exterior or interior veneer finish over concrete or masonry walls.
TechMix® High-Strength 5000 Concrete Mix is a commercial grade blend of aggregate, sand, and Portland cement specifically designed for higher early strength. Ideal for cold-weather applications, it achieves 5,000 psi after 28 days. Used for any application of 2" thick or greater. Available in 60# bags (BOM #101122) and 80# bags (BOM #104882).
Tech Mix® Masonry Cement is designed to be mixed with masonry sand to create masonry mortar for various applications such as brick and stone. Type N Masonry Cement (BOM #100920) is used for non-structural, above-grade applications such as setting brick or stone veneer and comes in a 70 lb. bag. Type S Masonry Cement (BOM #100917) is designed for structural above-grade or below-grade application and comes in a 75 lb. bag. Type M Masonry Cement (BOM #100868) is used for structural, below-grade, load-bearing walls where higher compressive strengths are needed and comes in a 70 lb. bag.
TechMix® Mason Sand (BOM#112144) is a consistent properly graded, fine, washed, and dried masonry sand. Refer to ASTM C270 for more information.
TechMix® Max Strength Concrete Mix (BOM #110259) is a commercial grade blend of fast-setting cement, sand, gravel, and other proprietary performance additives designed to provide extended working time and high early strength for concrete applications requiring a minimum thickness of 1½ in. (38 mm). Air-entrained for improved workability and freeze-thaw resistance, this mix is performance enhanced with corrosion inhibitors and contains fibers for crack resistance and increased toughness.
TechMix® Mortar Mix Type N (BOM #104881) is a blend of Portland cement, lime, and sand for laying brick, block, and stone for all types of construction.
TechMix® Mortar Mix Type S (BOM #104885) is a blend of Portland cement, lime, and sand for laying brick, block, and stone on either load-bearing or non-load-bearing walls. Suitable for construction below grade.
TechMix® Multi-Purpose Utility Sand (BOM #101004) is produced from high-purity industrial quartz for a use in a wide variety of applications that require a chemically inert, durable structural filler such as floor overlays, finish coat stucco, and sports turf. With consistently uniform grain shapes and particle distribution, this basic building material offers excellent compaction, placement, and mechanical properties. The high silica content is combined with low level soluble ions, alkalis, and alkaline oxides to provide non-reactive service in most corrosive and exposed environments.
TechMix® PCL Mortar Pro - Type N is a consistent, specifically-formulated blend of Portland cement, hydrated lime, and dried sand with superior bond, water retention, and board life. Used for multi-purpose interior and exterior masonry construction including laying brick, block, and stone. Type N is suitable for load-bearing, above-grade construction. Meets requirements of ASTM C270. Available in 80# bags (BOM #111207) and 3000# bulk bags (BOM #111118). PCL Mortar Pro is also available with preblended color and/or integral water repellant. For more information, contact your sales representative.
TechMix® PCL Mortar Pro - Type S is a consistent, specifically formulated blend of Portland cement, hydrated lime, and dried sand with superior bond, water retention, and board life. Used for multi-purpose interior and exterior masonry construction including laying brick, block, and stone. Type S is suitable for load-bearing construction above or below grade. Meets requirements of ASTM C270. Available in 80# bags (BOM #111217) and 3000# bulk bags (BOM #111119). PCL Mortar Pro is also available with preblended color and/or integral water repellant. For more information, contact your sales representative.
TechMix® Pool Filter Sand (BOM #100468) is a finely-graded, clean, dry, silica sand specially formulated for use in swimming pool filters.
Designed for use in a variety of applications, TechMix Portland Type III Cements (BOM #100722) are manufactured to meet virtually any construction challenge and meets all requirements as outlined in ASTM C150. Portland Type III Cements provides high early strength and are ideally suited for a variety of concrete construction applications. Type III is often used for those jobs where a structure must be put into service quickly, or when forms need to be removed as soon as possible, such as pre-cast or pre-stress applications.
TechMix® Premium Concrete Countertop Mix is a fast-setting, high-strength mix specially formulated to create countertops, outdoor kitchen tops, bar or table tops, workbench or utility tops. This product can also be used to produce precast wall caps, mantel or lintels for many different applications. Premium Concrete Countertop Mix needs only water to produce an easy-to-use, pourable mixture that can be de-molded in 18-24 hours. Available in a 50 lb. bag in gray (BOM #103434) or white (BOM #104082).
TechMix® Sand Topping Mix is a uniformly pre-blended Portland cement and sand mixture for placing concrete overlays 2" thick or less. Used for patching and leveling steps, slabs, walks, and floors. Available in 60 lb. bags (BOM #104880) and 80 lb. bags (BOM #112230)
TechMix® White Portland-Limestone Cement – Type I (BOM #112770) is used to produce a wide variety of architectural concrete products and applications. General applications include cast in place or precast wall panels, floors, slabs, terrazzo, thin set and tile grouts, cast stone, masonry units and mortars, stucco, swimming pools & spas, glass fiber reinforced concrete, ornamental statuary, floor tiles, concrete roof tiles, perimeter security, pavers and traffic safety items such as concrete median barriers, bridge parapets, pedestrian crosswalks, curbs and other delineators. White cement is often used to produce bright finishes, vibrant colors or ultra-high performance concretes that look great and provide structural performance that make them ideal for resilient building applications. White Portland-Limestone Cement meets ASTM C150 Standard Specification for Portland Cement, as well as AASHTO M85 and CSA A3001 specifications.