DIY Concrete


Akona® Concrete/Masonry Set Accelerator

Akona® Concrete/Masonry Set Accelerator (BOM #103963) is an ASTM C494, Type C, non-chloride, non-corrosive, liquid that improves workability and initial strength while it reduces the hydration time of cement. The product is recommended for use during cooler weather to accelerate set time and reduce the risk of frozen mortar and concrete mixes. It is also recommended for use when early strength gain is desired to speed up projects. Akona Concrete/Masonry Set Accelerator provides a reduced curing time, faster set time and increased early strength. The product speeds finishing operations in any weather condition without any corrosive effects.


Akona® Crack-Resistant Surface Bonding Cement

Akona® Crack-Resistant Surface Bonding Cement (BOM #102614) is a specially-formulated, multi-use product. It can be used to build and restore retaining walls or block walls, patch large vertical holes where non-sagging cement is a must, or repair deteriorated stucco. Because it contains special fibers it will not shrink, crack, or sag on a vertical repair. It also provides additional overall strength over conventional concrete.


Akona® Fast-Setting Anchoring Epoxy

Akona® Fast-Setting Anchoring Epoxy (BOM #120438) is a two-component, high-performance, 100% solids, high-modulus, non-sag gel epoxy designed for anchoring bolts, railings, dowels, and rebar steel into concrete and to bond or repair a variety of household and common building materials including concrete, porous tile, and stone. Special no-mess, self-mixing tube for easier application. Non-shrink, resistant to chemicals and solvents, this high-strength, fast-setting epoxy has a gel time in as little as 12-14 minutes; initial cure of 2 hours; and final cure time of 12-16 hours. Use both horizontal and vertical, up to 1/8" (3 mm) annular width and 10" (254 mm) depth. Because it is moisture tolerant, it is ideal for stopping air and water leaks. Gray in color.


Akona® Foundation Coating Cement

Akona® Foundation Coating Cement (BOM #102621) is a specially-formulated, cement-based product for coating and protecting polystyrene insulation board or insulated concrete forms (ICF) from weathering, ultraviolet rays, and general wear/impact. Akona Foundation Coating Cement is polymer-modified and contains fibers which reduces shrinkage and improves the adhesion properties of the product. Akona Foundation Coating Cement is easy to apply by masonry brush or trowel and has the superior durability of a Portland cement-based product. It also provides a tough, durable gray textured or stucco-like finish. If desired, the product may be integrally colored with a liquid cement or mortar colorant, or it can be painted to match existing home design.


Akona® Instant Patching Cement

Akona® Instant Patching Cement (BOM #102632) is a high-performance cement used for filling wide cracks and other concrete repair needs. It sets rock hard in just 90 minutes. Akona Instant Patching Cement self-bonds to all properly-prepared concrete surfaces and develops twice the strength of ordinary concrete.


QUIKRETE® Color Additive

QUIKRETE® Color Additive is a liquid coloring agent used to customize the color of your concrete project. Mix with water and then add to dry concrete mix. One bottle will mix with two 80 lb. or 60 lb. bags of Concrete Mix. Available in Red (BOM #105510), Brown (BOM #105508), Buff (BOM #105509), Charcoal (BOM #105507), and Terra Cotta (BOM #107832).


QUIKRETE® Crack-Resistant Concrete Mix

QUIKRETE® Crack-Resistant Concrete Mix (BOM #109358) is a construction grade blend of Portland cement, sand, gravel & special reinforcing fibers to reduce shrinkage cracks and improve impact resistance. Just add water and mix to create for walkways, patios, steps, garage or shed floors.


QUIKRETE® Fast-Setting Concrete Mix

QUIKRETE® Fast-Setting Concrete Mix (BOM #100166) is a special blend of fast-setting cements, sand and gravel designed to set hard in approx. 20 to 40 minutes. Sets posts without mixing. Pour dry mix into hole and soak with water. Use for setting fence posts, mailbox posts, basketball posts, deck posts, or lamp posts. Or use to construct new steps, sidewalks, or concrete appliance pads.


QUIKRETE® FastSet™ Repair Mortar

QUIKRETE® FastSet Repair Mortar (BOM #109719) is specifically formulated to make structural repairs to any concrete, masonry or stucco surface. This low-sag formula has a 20-30 minute working time which allows for sculpting of the material during placement and makes it ideal for vertical and overhead repairs. Just add water, mix, and use to repair concrete, masonry, or stucco surfaces. Exceeds ASTM C 928 R-2. Compressive strength ASTM C109 modified: 3 hours=2,000 psi, 24 hours = 4,000 psi, 7 days = 5,000 psi, and 28 days = 6,000 psi.


SAKRETE® 5000 Plus Concrete Mix

SAKRETE® 5000 Plus Concrete Mix (BOM #120020) is a professional grade concrete mix used for building and repairs greater than 2" depth.


SAKRETE® Crack Resistant Concrete Mix

Formulated to reduce the risk of surface shrinkage cracks, Sakrete Crack Resistant Concrete Mix is a professional strength blend of cementitious materials, sands, stone and fibers. For repair and building jobs where concrete thickness exceeds 2”.


SAKRETE® Fast-Setting Concrete Mix

SAKRETE® Fast-Setting Concrete Mix (BOM #120019 = 50 lb. pail / #106576 = 50 lb. bag) sets posts and poles quickly and easily, even without blending the material. Sets in just ½ an hour so that no bracing is needed and exceeds the strength requirements of ASTM C 387. Fast-Setting Concrete Mix is intended for applications requiring at least 2 inches in thickness.


SAKRETE® High Strength Concrete Mix

SAKRETE® High Strength Concrete Mix (BOM #100171 = 60 lb. bag / #120021 = 50 lb. pail) is designed for anchoring posts and poles, and pouring footings and slabs. High Strength Concrete Mix is premium quality for consistent strength and durability and meets ASTM C 387 strength requirements for structural applications. Uses include building walks, drives, slabs and steps as well as anchoring posts and poles. High Strength Concrete Mix is for applications requiring at least 2 inches in thickness. Just add water, mix, and use.


SAKRETE® Sand Mix

SAKRETE® Sand Mix (BOM #100397) is a quality mixture of sand and cement designed to be used as a topping mix to rejuvenate damaged concrete surfaces or as a bedding mix and joint grout for flagstone, slate, and brick walkways. Sand Mix can be applied in layers ranging from ½ to 2 inches thick and exceeds the strength requirements of ASTM C 387. Just add water, mix, and use.


TCC Materials® Countertop Mix

TCC Materials® Premium Concrete Countertop Mix™ is a fast-setting, high-strength countertop mix formulated for use in various precast projects. This product is ideally suited for countertops, outdoor kitchen tops, bar or table tops, precast wall caps, mantels or lintels. Because it is fiber reinforced with shinkage-reducing microfiber technology, this product is also ideal for workbenches and utility tops. Premium Countertop Mix just needs water to produce an easy-to-use, pourable mixture that can be de-molded in 18-24 hours. Available in a 50 lb. bag in gray (BOM #103434) or white (BOM #104082).


TECH-MIX® Concrete Mix

TECH-MIX® Concrete Mix (BOM #104879) is a high strength pre-blended Portland cement mixture for pouring concrete 2 inches thick or greater. Used for general building and repairing steps, slabs, walks, and floors.


 

 

SHARE