55 Gal

Tenon^® 40% Silane Sealer

Tenon® 40% Silane Sealer is a clear, solvent-based concrete sealer that penetrates deep into and reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and the spalling, freeze damage, and  rebar corrosion which moisture can cause. It is suitable for use to protect, and seal fully-cured fresh concrete, existing concrete, stucco, architectural concrete, and other cementitious materials. 40% Silane Sealer is used for above-grade exterior applications that are not subject to hydrostatic pressure.  Available in 1 gal. bottle (BOM #129870), 5 gal. pail (BOM #129860) and 55 gal. drum (BOM #129597). 

Tenon^® 40% Silane Sealer WB

Tenon® 40% Silane Sealer WB is a VOC compliant, clear, non-yellowing, concrete sealer that penetrates deeply and reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and spalling, freeze damage, and rebar corrosion due to moisture interaction. It is suitable for use to protect, and seal fully cured, new concrete, existing concrete, stucco, architectural concrete, and other cementitious materials. Tenon® 40% Silane Sealer WB is designed for use above-grade exterior applications that are not subjected to hydrostatic pressure. Available in 1 gal. bottle (BOM #114417), 5 gal. pail (BOM #114427) and 55 gal. drum (BOM #114415). 

Tenon^® Burnished Block Sealer WB Matte

Tenon®Burnished Block Sealer WB Matte is used as a final sealer on masonry block walls including burnish block or groundface block, architectural block, brick, slate, paving stone, terrazzo, quarry tile, and cementitious materials. It enhances the beauty, giving the surface a rich "wet-look" without the gloss. It forms a breathable membrane to increase protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these surfaces easier to clean. Made with a durable polysiloxane that does not yellow when exposed to the sun's UV rays. Available in a 1 gal. bottle (BOM #130090), 5 gal. pail (BOM #130080) and 55 gal. drum (BOM #129695).

Tenon^® Concrete & Mortar Dissolver RM

Tenon® Concrete & Mortar Dissolver RM is an environmentally-friendly liquid alternative to aggressive acid based concrete removers. Concrete & Mortar Dissolver RM is specifically designed for use in the ready-mix industry to clean equipment while the concrete and mortar are still in their plastic state. This product will retard the set time and prevent the cementitious bonds from forming, allowing the material to be easily washed from the equipment and tools.

Tenon^® Cure & Harden

Tenon® Cure & Harden is a clear, water-based silicate-based curing, hardening, and dustproofing concrete sealer. Tenon® Cure & Harden penetrates into and reacts chemically within the capillaries of the concrete or masonry surfaces. It is suitable for use on freshly placed and finished concrete and in the renovation of aged concrete.

Tenon^® Cure & Seal ES

Tenon® Cure & Seal ES is a clear, non-yellowing, fast drying acrylic compound.  No Fillers, oils, waxes, or saponifiable resins are contained in the mixture.  It is used for curing and sealing of freshly-placed and /or existing concrete, terrazzo, brick, stone, architectural concrete, and other cementitious materials.  Cure & Seal ES forms a membrane film on new concrete to seal and retain hydrations water, providing maximum hardness of the substrate, resistance to abrasion, and resistance to damage caused by salt, oil, grease, mild acids, alkali, and stains from soot, smog, fumes, and gases.  Cure & Seal ES will also benefit existing concrete by penetrating into the slab, binding together the small dusting particles, while filling the voids to produce a non-porous, dust-free, brighter surface.   When used on terrazzo, brick, stone, and architectural concrete, it brings out the highlights, enriches, and enhances the natural colors found in the material.

Tenon^® Dissipating Cure WB +PLUS

Tenon® Dissipating Cure WB +PLUS is a water-based, clear resin, liquid membrane forming, curing compound with silane used for moisture retention of freshly placed concrete. Designed for interior or exterior applications where a dissipating or easily removed curing compound is required. It is particularly recommended for applications where greater moisture retention is required . Tenon® Dissipating Cure WB +PLUS will pass all VOC compliance laws.

Tenon® Dissipating Cure WB +PLUS is available in 1 gal. bottle (BOM #114437), 5 gal. pail (BOM #114447), 55 gal. drum (BOM #114457), 275 gal. tote (BOM #114467) .

Tenon^® FormGuard

Tenon® FormGuard is a V.O.C. compliant, ready-to-use, petroleum based, chemically reactive liquid concrete form release agent. Tenon FormGuard effectively prevents bonding of concrete to forms and formliners. Use of Tenon FormGuard regularly will increase the life of all forms. Tenon FormGuard can be used on forms such as steel, aluminum, fiberglass-reinforced, all grades of plywood, epoxy-coated, and urethane-coated.

Tenon^® FormGuard Citrus

Tenon® FormGuard Citrus is a V.O.C. compliant, ready-to-use, petroleum based, chemically reactive liquid concrete form release agent. Tenon® FormGuard Citrus effectively prevents bonding of concrete to forms and form liners. Use of Tenon® FormGuard Citrus regularly will increase the life of all forms. Tenon® FormGuard Citrus can be used on forms such as steel, aluminum, fiberglass-reinforced, all grades of plywood, epoxy-coated, and urethane-coated.

Tenon^® Hardener LS

Tenon® Hardener LS is a clear, water-based Lithium Silicate-based hardening, and dustproofing concrete sealer.  Tenon® Hardener LS deeply penetrates into the concrete surface and reacts chemically within the capillaries of the concrete surfaces.  The reaction forms a dense calcium silicate hydrate crystalline structure, providing a hard durable surface. It is suitable for use on recently finished concrete and in the renovation of aged concrete greater than 10 days old.

Tenon^® Salt Barrier ES

Tenon® Salt Barrier ES (Exempt Solvent) is designed to protect & extend the life of concrete, masonry, pavers, retaining walls and other cementitious surfaces by protecting from the damaging effects of salt and de-icing chemicals without affecting the finished look. Salt Barrier ES provides a natural finish that maintains the original appearance of driveways, patios, garage floors, block walls, and other concrete or masonry surface. This clear, solvent-based formula penetrates and reacts chemically within the capillaries of the concrete to protect against moisture penetration, spalling, freeze-thaw damage, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants while making these surfaces easier to clean. Salt Barrier ES is used for above-grade exterior applications that are not subject to hydrostatic pressure.

Tenon^® Ultimate Barrier

Tenon® Ultimate Barrier is a clear, non-yellowing, fast drying acrylic-silicone blended concrete sealer for curing, dustproofing, and weatherproofing of freshly-placed and/or existing concrete, terrazzo, brick, stone, architectural concrete, and other cementitious materials. Tenon® Ultimate Barrier is designed to be a single application for curing, sealing, and weatherproofing. Tenon® Ultimate Barrier forms a membrane film on new concrete to seal and retain hydration water, providing optimum curing of the substrate, resistance to abrasion, damage caused by salt, oil, grease, mild acids, alkali, and stains from soot, smog, fumes, and gases. Tenon® Ultimate Barrier reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and the spalling, freeze damage, and rebar corrosion which moisture can cause. It is suitable for use to cure, protect, and seal fully-cured, new concrete, existing concrete, stucco, architectural concrete, and other cementitious materials.

Tenon^® Ultimate Barrier ES

Tenon® Ultimate Barrier ES is a VOC compliant, clear, non-yellowing, fast drying acrylic-silicone blended concrete sealer for curing, dustproofing, and weatherproofing of freshly-placed and/or existing concrete, terrazzo, brick, stone, architectural concrete, and other cementitious materials.

Tenon Ultimate Barrier ES is designed to be a single application for curing, sealing, and weatherproofing. Tenon® Ultimate Barrier ES forms a membrane film on new concrete to seal and retain hydration water, providing optimum curing of the substrate, resistance to abrasion, damage caused by salt, oil, grease, mild acids, alkali, and stains from soot, smog, fumes, and gases.

Tenon Ultimate Barrier ES reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and the spalling, freeze damage, and rebar corrosion which moisture can cause. It is suitable for use to cure, protect, and seal fully-cured, new concrete, existing concrete, stucco, architectural concrete, and other cementitious materials.

Tenon^® Air Entrainment

Tenon® Air Entrainment (BOM #120377) is a ready-to-use, aqueous solution made of organic materials.  Air Entrainment entrains a small and stable amount of air into the desired mix. These small, stable air voids enhance the mixture and improve workability. Its chemical composition and physical properties make it ideal for many construction applications. It is intended for use when increased workability and freeze-thaw durability of concrete or mortar is preferred. This admixture also improves resistance to freeze/thaw, scaling, segregation, and bleeding and improves strength, plasticity, water retention, and cohesiveness of mortar. Meets ASTM C260 Standard Specification for Air-Entraining Admixtures for Concrete.

Tenon^® SuperFlow

Tenon® SuperFlow water-reducing admixture is a full range water reducing additive providing a more plastic and flowable concrete. It produces concrete mixes with different levels of workability to include self-consolidating concrete (SCC) applications. Tenon SuperFlow admixture meets ASTM C494-C 494M compliance requirements for Type A water-reducing and Type F high-range water-reducing admixtures.

Tenon^® Burnished Block Sealer

Tenon® Burnished Block Sealer is used as a final sealer on masonry block walls including burnish block or ground face block, architectural block, brick, slate, paving stone, terrazzo, quarry tile, and cementitious materials. Burnished Block Sealer enhances the beauty, giving the surface a rich “wet-look” sheen. It forms a membrane to increase protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these surfaces easier to clean. Made with a blend of methacrylate polymers, this aromatic solvent-based coating does not yellow when exposed to the sun’s UV rays. Available in 1 gal. bottle (BOM #121100), 5 gal. pail (BOM #129530), and 55 gal. drum (BOM #121101).

Tenon^® Burnished Block Sealer WB

Tenon® Burnished Block Sealer WB is used as a final sealer on masonry block walls including burnish block or groundface block, architectural block, brick, slate, paving stone, terrazzo, quarry tile, and cementitious materials. Burnished Block Sealer WB enhances the beauty, giving the surface a rich “wet-look” sheen. It forms a breathable membrane to increase protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these surfaces easier to clean. Made with an acrylic that does not yellow when exposed to the sun's UV rays. Available in 1 gal. bottle (BOM#121110), 5 gal. pail (BOM#121107), and 55 gal. drum (BOM#121113).

Tenon^® Concrete & Masonry Dissolver

Tenon® Concrete & Masonry Dissolver is an environmentally-friendly liquid alternative to aggressive acid concrete removers. Use to safely dissolve and remove cured concrete, mortar, grout, and stucco build-up from tools, concrete forms, job mixers, hardware, shoring, and more.

Tenon^® Cure & Seal WB 1315

Tenon® Cure & Seal WB 1315 is a film-forming compound that meets ASTM C1315 performance standards for water loss when applied properly to cure, seal, and harden freshly placed concrete, terrazzo, brick, stone, architectural concrete, and other cementitious materials. Cure & Seal WB 1315 will pass all VOC compliance laws and is formulated to cure, seal, protect, and dustproof concrete, as well as seal many types of porous tile and resilient floors. Designed for both exterior and interior applications, it is particularly recommended for indoor work in public buildings (hospitals, restaurants) and private residences where solvent-based systems are difficult to use. The white solution dries clear and provides a dust-free surface. This product provides maximum hardness to the concrete as well as resistance to traffic abrasion. Construction debris are easier to clean. Compatible with most tile and carpet adhesives.  Available in 1 gal. bottle (BOM #129910), 5 gal. pail (BOM #129920), and 55 gal. drum (BOM #129930).

Tenon^® Cure & Seal

Tenon® Cure & Seal is a non-yellowing, fast-drying acrylic compound used for curing, sealing, and hardening of freshly-placed and/or existing concrete. Enhances colors, darkens the appearance of concrete, brick, stone, terrazzo, and exposed aggregate. Available in 1 gal. bottle (BOM #120839), 5 gal. pail (BOM #120838), or 55 gal. drum (BOM #120932).

Tenon^® Cure & Seal WB

Tenon® Cure & Seal WB is a clear, non-yellowing, acrylic polymer membrane forming compound used for curing, sealing, and hardening of freshly-placed and/or existing concrete, terrazzo, brick, stone, architectural concrete, and other cementitious materials. Waterborne mixture passes VOC compliance laws. Available in 1 gal. bottle (BOM #120823), 5 gal. pail (BOM #120822), and 55 gal. drum (BOM #120824).

Tenon^® Dissipating Cure 1315 WB

Tenon® Dissipating Cure 1315 WB is a water-based, clear resin, liquid membrane forming, curing compound used for moisture retention of freshly placed concrete. Tenon® Dissipating Cure 1315 WB is formulated for curing concrete. Designed for interior or exterior applications where a dissipating or easily removed curing compound is required. It is particularly recommended applications where greater moisture retention is required . Tenon® Dissipating Cure 1315 WB will pass all VOC compliance laws. Available in 5 gallon pails (BOM #113839), 55 gallon drums (BOM #113839), and 275 gallon totes (BOM #113838).

Tenon^® Wax Cure 1315 WB

Tenon® Wax Cure 1315 WB is a water-based, white pigmented, liquid membrane forming, wax curing compound used for moisture retention of freshly placed concrete. Tenon® Wax Cure 1315 WB is formulated for curing concrete. The addition of white pigment to the wax film reflects the heat of the sun to protect excess heat build-up. Designed for exterior applications, it is particularly recommended for roadways, airport runways, parking lots, and other pavement projects where greater moisture retention is required . Tenon® Wax Cure 1315 WB will pass all VOC compliance laws. Available in 5 gallon pails (BOM #113830), 55 gallon drums (BOM #113829), and 275 gallon totes (BOM #113828).

Tenon^® Wax Cure 309 WB

Tenon® Wax Cure 309 WB is a water-based, white pigmented, liquid membrane forming, wax curing compound used for moisture retention of freshly placed concrete. Tenon® Wax Cure 309 WB is formulated for curing concrete. The addition of white pigment to the wax film reflects the heat of the sun to protect excess heat build-up. Designed for exterior applications, it is particularly recommended for slip form , curb and gutter, and municipal sidewalk applications where minimum moisture retention is required. Tenon® Wax Cure 309 WB will pass all VOC compliance laws. Available in 50 lb. pails (BOM #113860), 55 gallon drums (BOM #113849), and 275 gallon totes (BOM #113851).

Tenon^® Mighty Bond^™

Tenon® Mighty Bond™ is a high-solids, acrylic, liquid bonding agent that substantially improves adhesion, impact, and shear bond, tensile, and flexural and compressive strength of unmodified concrete, mortars, patches and grouts. Additionally, Mighty Bond adds excellent freeze/thaw and salt resistance and creates more durable cement-based materials. Minimal preparation is required. Available in 1 gal. bottles (BOM #120525), 5 gal. pails (BOM #120526) and 55 gal. drums (BOM #130020).

Tenon^® Paver Guardian

Tenon® Paver Guardian is designed to protect & extend the life of installed pavers without changing the finished look. Paver Guardian provides a natural finish that maintains  the original look of pavers, concrete, architectural concrete, brick, natural stone, and other cementitious materials. This clear, solvent-based formula penetrates and reacts chemically within the capillaries of the concrete to protect against moisture  penetration, spalling, freeze-thaw damage, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants while making these surfaces easier to clean. Paver Guardian is used for above-grade exterior applications that are not subject to hydrostatic pressure. Available in 1 gal. bottle (BOM #129670), 5 gal. pail (BOM #129660), or 55 gal. drum (BOM #129534).

Tenon^® Paver Guardian WB

Tenon® Paver Guardian WB is designed to protect & extend the life of installed pavers, retaining walls and other cementitious surfaces without affecting the finished look. Paver Guardian WB provides a natural finish that maintains the original look of pavers, concrete, architectural concrete, brick, natural stone, and other cementitious materials. This clear, water-bourne formula penetrates and reacts chemically within the capillaries of the surface to protect against deicing salts, moisture penetration, spalling, freeze-thaw damage,  efflorescence, and chemical erosion. Paver Guardian WB also protects surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants while making these surfaces easier to clean. Paver Guardian WB is used for above-grade exterior applications that are not subject to hydrostatic pressure. Available in 1 gal. bottle (BOM #129780), 5 gal. pail (BOM #129790), or 55 gal. drum (BOM #129576).

Tenon^® Paver Seal

Tenon® Paver Seal is designed to protect & extend the life of installed pavers, while enhancing the color and adding a matte finish. Made with a blend of methacrylate polymers, this solvent -based coating does not yellow when exposed to the sun’s UV rays and can also be used as a final sealer on concrete, architectural concrete, brick, natural tile, and other cementitious materials. Paver Seal will enhance the beauty of pavers, colored or stamped concrete, or exposed aggregate yet keep a matte finish. It forms a membrane to increase protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these surfaces easier to clean. Available in 1 gal. bottle (BOM #129730), 5 gal. pail (BOM #129720), or 55 gal. drum (BOM #129551).

Tenon^® Paver Seal Pro WB

Tenon® Paver Seal Pro WB is a penetrating, breathable, waterborne sealer designed to protect & extend the life of installed pavers, while enhancing the color with a natural, non-gloss finish. Made with a durable polysiloxane that does not yellow when exposed to the sun's UV rays, it penetrates deep in the capillaries of the paving stones for increased protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion. Paver Seal Pro WB will enhance the beauty of pavers, stone veneer, and architectural concrete by making colors more vibrant while protecting surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants and making these surfaces easier to clean. Available in 1 gal. bottle (BOM #129770), 5 gal. pail (BOM #129760), or 55 gal. drum (BOM #129563).

Tenon^® Paver Seal & Shine

Tenon® Paver Seal & Shine is designed to protect & extend the life of installed pavers, while enhancing color and adding a gloss finish. Made with a blend of methacrylate polymers, this solvent-based coating does not yellow when exposed to the sun’s UV rays and can also be used as a final sealer on concrete, architectural concrete, brick, natural stone, and other cementitious materials. Paver Seal & Shine will enhance the beauty of pavers, colored or stamped concrete, or exposed aggregate by giving it a rich “wet-look” gloss. It provides a membrane to increase protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these  surfaces easier to clean. Available in 1 gal. bottle (BOM #129690), 5 gal. pail (BOM #129680), or 55 gal. drum (BOM #129539).

Tenon^® Paver Seal & Shine Pro WB

Tenon® Paver Seal & Shine Pro WB is a penetrating, breathable, waterborne sealer designed to protect & extend the life of installed pavers, while enhancing the color and adding a “wet-look” gloss. Made with a durable acrylic that does not yellow when exposed to the sun's UV rays, it penetrates deep in the capillaries of the paving stones for increased protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion. Paver Seal & Shine Pro WB will enhance the beauty of pavers, colored or stamped concrete, or exposed aggregate by giving it a “wet-look” finish while protecting surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants and making these surfaces easier to clean. Available in 1 gal. bottle (BOM #129710), 5 gal. pail (BOM #129700), or 55 gal. drum (BOM #129545). 

Tenon^® Paver Seal Ultra Shine

Tenon® Paver Seal Ultra Shine is a high-solids, low-viscosity, sprayable sealing agent designed to protect & extend the life of installed pavers, while enhancing color and adding a high-gloss “wet look” finish. Made with a blend of 100% methacrylate polymers, this solvent-based coating does not yellow when exposed to the sun’s UV rays and can also be used as a final sealer on architectural concrete, brick, natural stone, and other cementitious materials. Paver Seal Ultra Shine will enhance the beauty and vibrancy of colored or stamped concrete and exposed aggregate giving it a rich high-gloss finish. It forms a membrane to increase protection from  damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these surfaces easier to clean. Available in 1 gal. bottle (BOM #129750), 5 gal. pail (BOM #129740), or 55 gal. drum (BOM #129556).

Tenon^® Salt Barrier

Tenon® Salt Barrier is designed to protect & extend the life of concrete, masonry, pavers, retaining walls and other cementitious surfaces by protecting from the damaging effects of salt and de-icing chemicals without affecting the finished look. Salt Barrier provides a natural finish that maintains the original appearance of driveways, patios, garage floors, block walls, and other concrete or masonry surfaces. This clear, solvent-based formula penetrates and reacts chemically within the capillaries of the concrete. This product protects against moisture  penetration, spalling, freeze-thaw damage, deicing salts, efflorescence, and chemical erosion. It also protects surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants while making those surfaces easier to clean. Salt Barrier is used for above-grade exterior applications that are not subject to hydrostatic pressure.

Tenon^® Salt Barrier WB

Tenon® Salt Barrier WB is designed to protect & extend the life of concrete, masonry, pavers, retaining walls and other cementitious surfaces by protecting from the damaging effects of salt and de-icing chemicals without affecting the finished look. Salt Barrier WB provides a natural finish that maintains the original appearance of driveways, patios, garage floors, block walls, and other concrete or masonry surfaces. This clear, water -based formula penetrates and reacts chemically within the capillaries of the surface to protect against deicing salts, moisture penetration, spalling, freeze-thaw damage, efflorescence, and chemical erosion. Salt Barrier WB also protects surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants while making these surfaces easier to clean. Salt Barrier WB is used for above-grade exterior applications that are not subject to hydrostatic pressure. Available in 1 gal. bottle (BOM #129840), 5 gal. pail (BOM #129580), or 55 gal. drum (BOM #129587).

Tenon^® 100% Silane Sealer

Tenon® 100% Silane Sealer is a clear, solvent-based, concrete sealer that penetrates deep into, and reacts chemically, within the capillaries of the concrete or masonry in order to protect against moisture penetration and the spalling, freeze damage, and  rebar corrosion which moisture can cause. It is suitable for use to protect and seal fully-cured fresh concrete, cast in place, precast, and high strength concrete materials. 100% Silane Sealer is used for above-grade exterior applications that are not subject to hydrostatic pressure. It is excellent for treating high traffic areas or surfaces that receive high salt concentrations such as coastal piers.  Available in 1 gal. bottle (BOM #129890), 5 gal. pail (BOM #129900) and 55 gal. drum (BOM #129652). 

Tenon^® 20% Silane Sealer

Tenon® 20% Silane Sealer is a clear, solvent-based concrete sealer that penetrates deep into and reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and the spalling, freeze damage, and  rebar corrosion which moisture can cause. It is suitable for use to protect, and seal fully-cured, new concrete, existing concrete, stucco, architectural concrete, and other cementitious materials. Silane sealers are used for above-grade exterior applications that are not subject to hydrostatic pressure. Available in 1 gal. bottle (BOM #129980), 5 gal. pail (BOM #129970) and 55 gal. drum (BOM #129644). 

Tenon^® Siloxane Final Seal

Tenon® Siloxane Final Seal is an aromatic, solvent-based concrete sealer/water-repellant used to protect cementitious surfaces against the damage caused by water penetration. Can be applied to surfaces where a cure and seal coating was previously applied. Available in 1 gal. bottle (BOM #120828), 5 gal. pail (BOM #120827), and 55 gal. drum (BOM #120829).

Tenon^® Siloxane Sealer

Tenon® Siloxane Sealer is a clear, solvent-based sealer for concrete and cementitious materials. It penetrates and reacts chemically within the capillaries to repel water and protect from the damaging effects of rain, water penetration, chemicals, salt, freeze-thaw cycles, and smog. Provides natural-looking, non-yellowing, invisible protection.  Available in 1 gal. bottle (BOM #120826), 5 gal. pail (BOM #120825), and 55 gal. drum (BOM #120829).

Tenon^® Super Clear Coat

Tenon® Super Clear Coat is used for curing and sealing exposed aggregate and sealing colored concrete. This aromatic solvent-based coating does not yellow when exposed to the sun’s UV rays and can also be used as a final sealer on burnish block, architectural concrete, brick, slate, paving stone, terrazzo, quarry tile, and cementitious materials. Enhances the colors of the surfaces with a rich "wet-look" sheen. Available in 1 gal. bottle (BOM #120831), 5 gal. pail (BOM #120830), and 55 gal. drum (BOM #120832).

Tenon^® Super Diamond Glaze

Tenon® Super Diamond Glaze is a higher viscosity version of Super Clear Coat used for curing and sealing exposed aggregate and sealing colored concrete. Enhances the beauty and depth of the surface, giving it a rich "wet-look" high gloss while protecting from the damages caused by moisture penetration. Available in 1 gal. bottle (BOM #120836), 5 gal. pail (BOM #120835), and 55 gal. drum (BOM #120837).