SEALERS


ProSpec® Concrete & Masonry Sealer WB

ProSpec® Concrete & Masonry Sealer WB is a water-based sealer that penetrates and reacts chemically within the capillaries of the concrete or masonry, bonding to the silica in the substrate to protect against moisture penetration, water-related staining, atmospheric chemicals, and deterioration. It is used to protect and seal clean, dry, coating-free, fully-cured concrete, brick masonry, concrete masonry units, stucco, stone terrazzo, architectural concrete, and some natural stones. For above-grade exterior applications that are not subject to hydrostatic pressure. Ready-to-use, this low VOC, silane/siloxane emulsion is especially suited for applications where VOC regulations for AIM coatings prevent the use of solvent-borne products. Available in 1 gallon bottles (BOM #120673) and 5 gallon pails (BOM #120674).


ProSpec® Cure & Seal

ProSpec® Cure & Seal is a non-yellowing, fast-drying acrylic compound used for curing, sealing, and hardening of freshly-placed and/or existing concrete. Enhances colors, darkens the appearance of concrete, brick, stone, terrazzo, and exposed aggregate. Available in 1 gal. bottle (BOM #120839), 5 gal. pail (BOM #120838), or 55 gal. drum (BOM #120932).


ProSpec® Cure & Seal WB

ProSpec® Cure & Seal WB is a clear, non-yellowing, acrylic polymer membrane forming compound used for curing, sealing, and hardening of freshly-placed and/or existing concrete, terrazzo, brick, stone, architectural concrete, and other cementitious materials. Waterborne mixture passes VOC compliance laws. Available in 1 gal. bottle (BOM #120823), 5 gal. pail (BOM #120822), and 55 gal. drum (BOM #120824).


ProSpec® Siloxane Final Seal

ProSpec® Siloxane Final Seal is an aromatic, solvent-based concrete sealer/water-repellant used to protect cementitious surfaces against the damage caused by water penetration. Can be applied to surfaces where a cure and seal coating was previously applied. Available in 1 gal. bottle (BOM #120828), 5 gal. pail (BOM #120827), and 55 gal. drum (BOM #120829).


ProSpec® Super Clear Coat

ProSpec® Super Clear Coat is used for curing and sealing exposed aggregate and sealing colored concrete. This aromatic solvent-based coating does not yellow when exposed to the sun’s UV rays and can also be used as a final sealer on burnish block, architectural concrete, brick, slate, paving stone, terrazzo, quarry tile, and cementitious materials. Enhances the colors of the surfaces with a rich "wet-look" sheen. Available in 1 gal. bottle (BOM #120831), 5 gal. pail (BOM #120830), and 55 gal. drum (BOM #120832).


ProSpec® Super Clear Coat Matte

ProSpec® Super Clear Coat Matte is used for curing and sealing exposed aggregate and sealing colored concrete. This aromatic, solvent-based sealer does not yellow under the sun's UV rays. It enhances the beauty of colored or stamped concrete and exposed aggregate yet keeps a matte, low gloss finish. Available in 1 gal. bottle (BOM #120834), and 5 gal. pail (BOM #120833).


ProSpec® Super Diamond Glaze

ProSpec® Super Diamond Glaze is a higher viscosity version of Super Clear Coat used for curing and sealing exposed aggregate and sealing colored concrete. Enhances the beauty and depth of the surface, giving it a rich "wet-look" high gloss while protecting from the damages caused by moisture penetration. Available in 1 gal. bottle (BOM #120836), 5 gal. pail (BOM #120835), and 55 gal. drum (BOM #120837).


ProSpec® TraxGrip

ProSpec® TraxGrip gives a light texture to concrete flatwork for a slip-resistant surface. Often used commercially on entrance floors, garage floors, steps, patios, walkways, and any surface where additional texture is desired to increase non-slip characteristics. TraxGrip is an optically clear thermoset polymer resin. Nearly invisible on the applied floor surface, it is added to curing and sealing compounds then applied to surfaces in the liquid solution. Available in 3.2 oz (BOM #120930) and 1 lb. (BOM #120927)


ProSpec® Dissipating Cure WB

ProSpec® Dissipating Cure WB (1 gal. BOM #120841, 5 gal. BOM #120840) is designed for curing and hardening freshly placed concrete surfaces. It is a water-based hydrocarbon resin compound. Concrete strength can be reduced by up to 40% if not properly cured, and can result in surface cracking, crazing, curling, and dusting. Complete hydration is reached with Dissipating Cure WB by acting to retain 95% of the moisture present in the fresh concrete for a minimum of 72 hours. This restriction of evaporation allows the concrete to reach maximum density and hardness. Dissipating Cure WB becomes chemically brittle in about 4 weeks after application. Curing compounds are not protective sealers or wear coatings and must be removed from the surface prior to application of liquid floor hardeners, penetrating coatings such as silanes, or cementitious toppings. Will wear off most surfaces with normal traffic, sunlight and/or weathering, any residue of Dissipating Cure WB can be removed with a power sweeper, hard brooming, and/or pressure washing, making the surface suitable for coatings, water-repellant sealers or for acid etching done preceding epoxy or urethane top coatings.


 

 

SHARE