ProSpec®


 

ProSpec® Air Entrainment

ProSpec® Air Entrainment (BOM #120377) is a ready-to-use, aqueous solution made of organic materials. ProSpec Air Entrainment entrains a small and stable amount of air into the desired mix. These small, stable air voids enhance the mixture and improve workability. Its chemical composition and physical properties make it ideal for many construction applications. It is intended for use when increased workability and freeze-thaw durability of concrete or mortar is preferred. This admixture also improves resistance to freeze/thaw, scaling, segregation, and bleeding and improves strength, plasticity, water retention, and cohesiveness of mortar. Meets ASTM C260 Standard Specification for Air-Entraining Admixtures for Concrete.


ProSpec® Air-Entrained Concrete Patching Mix AE

ProSpec® Air-Entrained Concrete Patching Mix AE (3U58M) (BOM #126199) is an ideal for repairing concrete pavement, bridge decks, industrial floors, concrete parking lots, and garage decks. This pre-blended mixture of cement, aggregate, and special additives will produce a high strength concrete repair material that is extremely durable and works well in harsh environments. Additionally, when used with ProSpec Fast-Set Liquid Activator, surfaces can be reopened to traffic within 4 to 5 hours under typical conditions.


ProSpec® Concrete & Masonry Dissolver

ProSpec® Concrete & Masonry Dissolver is an environmentally-friendly liquid alternative to aggressive acid concrete removers. Use to safely dissolve and remove cured concrete, mortar, grout, and stucco build-up from tools, concrete forms, job mixers, hardware, shoring, and more. Available in 1 gal. bottle (BOM #120911) and 5 gal. pail (BOM #120912).


ProSpec® Concrete & Masonry Sealer WB

ProSpec® Concrete & Masonry Sealer WB is a water-based sealer that penetrates and reacts chemically within the capillaries of the concrete or masonry, bonding to the silica in the substrate to protect against moisture penetration, water-related staining, atmospheric chemicals, and deterioration. It is used to protect and seal clean, dry, coating-free, fully-cured concrete, brick masonry, concrete masonry units, stucco, stone terrazzo, architectural concrete, and some natural stones. For above-grade exterior applications that are not subject to hydrostatic pressure. Ready-to-use, this low VOC, silane / siloxane emulsion is especially suited for applications where VOC regulations for AIM coatings prevent the use of solvent-borne products. Available in 1 gallon bottles (BOM #120673) and 5 gallon pails (BOM #120674).


ProSpec® Concrete Patching Mix

ProSpec® Concrete Patching Mix (BOM 126198) is a dry mixed combination of Portland Cement and aggregates that is proportioned and manufactured according to MnDOT specification 3105. When mixed according to specifications with water and admixtures, it is an ideal mixture for repairing concrete pavement, industrial floors, and structural concrete.


ProSpec® Concrete Resurfacer

ProSpec® Concrete Resurfacer (BOM #120728) is a fast-setting, high-performance polymer-modified, cement-based product used for resurfacing old concrete to make it look new again. Applications from feather edge to ½ in. (2-13 mm). Fast-drying, walkable on average in 2 hours.


ProSpec® Cure & Seal

ProSpec® Cure & Seal is a non-yellowing, fast drying acrylic compound used for curing, sealing, and hardening of freshly-placed and/or existing concrete. Enhances colors, darkens the appearance of concrete, brick, stone, terrazzo, and exposed aggregate. Available in 1 gal. bottle (BOM #120839), 5 gal. pail (BOM #120838, or 55 gal. drum.


ProSpec® Cure & Seal WB

ProSpec® Cure & Seal WB is a clear, non-yellowing, acrylic polymer membrane forming compound used for curing, sealing, and hardening of freshly-placed and/or existing concrete, terrazzo, brick, stone, achitectural concrete, and other cementious materials. Waterborne mixture passes VOC compliance laws. Avaiable in 1 gal. bottle (BOM #120823), 5 gal. pail (BOM #120822, and 55 gal. drum (BOM #120824).


ProSpec® Fast-Set Liquid Activator

ProSpec® Fast-Set Liquid Activator is formulated specifically to be used in conjunction with ProSpec® Air-Entrained Concrete Patching Mix AE in order to establish a quicker set and develop strength rapidly. When used with the patching mix, Fast-Set Liquid Activator reduces the closure time of high-traffic areas from 24 hours to 4-5 hours under normal conditions. Available in 1 gallon bottles (BOM #120593) and 5 gallon pails (BOM # 120770).


ProSpec® Feather Edge Pro

ProSpec® Feather Edge Pro (BOM #120540) is a trowelable, rapid-setting, polymer-modified, self-drying, Portland cement-based patch and skim coating compound for multiple interior substrates. Specially formulated with superior workability for easy application, this non-sanded product results in an ultra-smooth finish and can be applied from feather-edge to ½ in. (13 mm) and is ideal for use as an embossing leveler. Fast-setting, with initial set in 15 minutes; can accept ceramic tile and stone applications, as well as moisture-sensitive floor coverings, in as little as 30 minutes or when completly dry.


ProSpec® Feather Patch Pro

ProSpec® Feather Patch Pro is a fast-setting, polymer-modified, self-drying, Portland cement-based patch and skim coating compound for interior use under ceramic tile, hardwood flooring, carpet and a wide array of floor coverings. Ideal for deeper patching, this product can be applied from feather-edge to 2 in. (51 mm) thick. Formulated for exceptional bond strength and superior workability, can be applied to concrete with a relative humidity (RH) up to 90%. Rapid-setting, with initial set in 15 minutes; can accept ceramic tile and stone applications, as well as moisture-sensitive floor coverings, in as little as 30 minutes or when completely dry. Available in 10 lb. (4.5 kg) pails (BOM #120618), and 25 lb. (11.3 kg) pails (BOM #120541).


ProSpec® Heavy-Duty Stone Veneer Mortar

ProSpec® Heavy-Duty Stone Veneer Mortar (BOM #120444) is a high-yield, lightweight, high-performance, polymer-modified, fiber-reinforced, Portland-cement based mortar for adhered installation of masonry veneer stone and natural stone. 25% lighter than traditional mortars with excellent non-sag and non-slump handling characteristics. Special admixtures help create both a mechanical and chemical bond to the substrate, significantly outperforming standard mortars. ProSpec Heavy-Duty Stone Veneer Mortar is "Step 2" of the ProSpec stone installation system used to create decorative exterior and non-load bearing interior veneer walls.


ProSpec® Level-Flo® Primer

ProSpec® Level-Flo® Primer is a high-quality, liquid-polymer latex for interior use with ProSpec Level-Flo self-leveling and concrete repair products. Applied to porous surfaces, this substrate primer reduces water absorption to ensure a flowable mix and promotes bonding. ProSpec Level-Flo Primer or Primer Pro are required to be applied to all substrates before placing ProSpec Level-Flo Underlayments or Wear-Toppings. Available in 1 gal. bottles (BOM #127201) and 5 gal. pails (BOM #127205).


ProSpec® Level-Flo® Underlayment 100

ProSpec® Level-Flo® Underlayment 100 (BOM #120534) is a Portland cement-based, self-leveling underlayment used to level and smooth interior floors for finished floor covering installation. Can be applied from ⅛"-1½" (3-38 mm) neat and up to 5" (127 mm) extended.. Accepts non-moisture sensitive tile and stone in as little as 24 hours, and moisture sensitive floor coverings in 3 days. Use with ProSpec Level-Flo Primer or Primer Pro to level and smooth over many interior substrates including concrete, existing ceramic tile, non-water soluable adhesive residue, and solid wood floors.


ProSpec® Level-Flo® Underlayment 200

ProSpec® Level-Flo® Underlayment 200 (BOM #120535) is a high-performance, fiber-reinforced, non-gypsum based, self-leveling underlayment that provides a flat, extremely smooth, durable surface for finished floorcovering installation. Can be applied from ⅛"-2" (3-51mm) neat, and up to 5" (127 mm) extended. Fast-setting, accepts non-moisture sensitive tile and stone in as little as 4 hours, and moisture sensitive floorcoverings in 16-24 hours. Use with ProSpec Level-Flo Primer or Primer Pro to level and smooth over many interior substrates including concrete, existing ceramic tile, non-water soluable adhesive residue, and solid wood floors.


ProSpec® Level-Flo® Underlayment 300

ProSpec® Level-Flo® Underlayment 300 (BOM #120536) is a high-performance, fiber-reinforced, non-gypsum based, self-leveling underlayment that provides a flat, extremely smooth, durable surface for finished floorcovering installation. Designed for fast leveling of floors where increased strength is required; reaching 28-day ASTM C109 Compressive Strength of 6,000 psi. Can be applied from ⅛"-2" (3-51 mm) neat, and up to 5" (127 mm) extended. Fast-setting, accepts non-moisture sensitive tile and stone in as little as 3-4 hours, and moisture sensitive floorcoverings in 6 hours. Use with ProSpec Level-Flo Primer or Primer Pro to level and smooth over many interior substrates including concrete, existing ceramic tile, non-water soluable adhesive residue, and solid wood floors.


ProSpec® Level-Flo® Underlayment 50

ProSpec® Level-Flo® Underlayment 50 (BOM #120585) is a Portland cement-based, self-leveling underlayment used to level and smooth interior floors for finished floor covering installation. Can be applied as thick as 1" down to ⅛" (25-3 mm). Accepts non-moisture sensitive tile and stone in as little as 24 hours, and moisture sensitive floor coverings in 3 days. Excellent for encapusulating radiant heat systems. Use with ProSpec Level-Flo Primer or Primer Pro to level and smooth over many interior substrates including concrete, existing ceramic tile, non-water soluable adhesive residue, and solid wood floors.


ProSpec® Metro Mix 240

ProSpec® Metro Mix 240 (BOM 128260) is a high performance concrete mix engineered to meet commercial/industrial ready mix specifications. Super plasticized for higher slump and compressive strengths with corrosion inhibitors. Ideal for projects requiring small structural concrete applications or when ready mix truck access is restricted. Use for structural applications and full depth repairs of 2" (51 mm) or greater. Exceeds ASTM C 387.


ProSpec® Metro Mix 240 AE

ProSpec® Metro Mix 240 AE (BOM 128270) is the air-entrained version of our high performance concrete mix engineered to meet commercial/industrial ready mix specifications. Super plasticized for higher slump and compressive strengths with corrosion inhibitors. Ideal for projects requiring small structural concrete applications or when ready mix truck access is restricted. Use for structural applications and full depth repairs of 1½" (51 mm) or greater. Exceeds ASTM C 387.


ProSpec® Mighty Bond™

ProSpec® Mighty Bond™ is a high-solids, acrylic, liquid bonding agent that substantially improves adhesion, impact, and shear bond, tensile, and flexural and compressive strength of unmodified concrete, mortars, patches and grouts. Additionally, Mighty Bond adds excellent freeze/thaw and salt resistance and creates more durable cement-based materials. Minimal preparation is required. Available in 5 gal. pails (BOM #120526) and 1 gal. bottles (BOM #120525).


ProSpec® Moisture Barrier

ProSpec® Moisture Barrier (BOM #127610) is an advanced, latex, polymer-based technology used as a water-resistant membrane applied to all wood or moisture-sensitive backup walls prior to application of ProSpec Polymer-Modified Stone Veneer Base Coat. Ready to use (no mixing required), with exceptional flexibility and elongation, solvent free and VOC compliant, ProSpec Moisture Barrier is part of the ProSpec veneer stone installation system. Color will be light purple when applied, dries to dark purple.


ProSpec® Non-Shrink Construction Grout 6000

ProSpec® Non-Shrink Construction Grout 6000 (BOM #120720) is a non-shrink, non-metallic, Portland cement based mixture of hydraulic cement, aggregate, and additives for general purpose structural grouting. Meets or exceeds ASTM C-1107.


ProSpec® Partial Depth Concrete Patch

ProSpec® Partial Depth Concrete Patch is is ideal for placing overlays less than 2” deep (5 cm). This pre-blended cement and oven dried sand mixture will produce a high-strength concrete repair material that is extremely durable in partial depth applications such as concrete pavements, bridge decks, industrial floors, concrete parking lots and garage decks. It is also used for adhering pavers to concrete steps and walks, patching and/or leveling concrete surfaces, filling large cracks, and filling cores in masonry block or brick. Available in 2:1 mix (BOM #120722), 2.5:1 mix (BOM #120723), or 3:1 mix (BOM #120724) (fine sand aggregate to Portland cement ratio).


ProSpec® Polymer-Modified Stone Veneer Base Coat

ProSpec® Polymer-Modified Stone Veneer Base Coat (BOM #120442) is used as a scratch and base coat for real or manufacatured stone veneer units. Also referred to as a cement plaster coating, it is a blend of cementitious materials, oven-dried masonry sand, and special performance admixtures designed to produce a highly-bondable substrate and to optimize consistency between batches. Special admixtures help create both a mechanical and chemical bond to the substrate with excellent workability and non-sag performance. Polymer-modified, mix with water only. "Step 1" of the ProSpec stone veneer installation system used to create decorative exterior or non-load bearing interior veneer walls.  Can be applied over ProSpec Moisture Barrier or directly to fully cured concrete.


ProSpec® Pourable Concrete Patch

ProSpec® Pourable Concrete Patch (BOM #120672) is a Portland cement-based, flowable, squeegee-grade, polymer-modified patching and resurfacing mix for interior and exterior horizontal concrete substrates. Easy to use, it corrects defects up to ½ in. (13 mm) on concrete surfaces prior to applying new flooring materials or coatings. Depending on application, can also be used as a wearable surface for residential and light duty commercial applications. Meets ASTM C387 “Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete” for normal weight concrete.


ProSpec® PVT Masonry Veneer Joint Grout

ProSpec® PVT Masonry Veneer Joint Grout is blend of dry, cementitious materials, performance admixtures, and masonry sand specifically designed to fill or tuck-point the joints between artificial stone, brick, masonry, and natural stone in veneer systems. Preblended with air-entrainment admixtures to resist freeze-thaw conditions, while increasing flow and durability. ProSpec Pro Veneer Technology (PVT) creates a high-performance professional grout, formulated for clean installation and flow properties to eliminate clogging when using a grout bag. Available in: Natural Gray (BOM #120463); White (BOM #120464); Tan (BOM #120465); and Brown (BOM #120466).


ProSpec® PVT Masonry Veneer Mortar

ProSpec® PVT Masonry Veneer Mortar (BOM #120461) is a high-performance, multi-purpose, polymer-modified mortar, used for both traditional thick bed scratch and base coats and as the bonding mortar for installing real or manufactured masonry veneer units. A blend of cementitious materials, oven-dried masonry sand, and special performance admixtures, our Pro Veneer Technology (PVT) creates both a mechanical and chemical bond to the substrate, significantly outperforming standard Type S and N mortars. Can also be used for grouting, yet is excellent for applications such as dry stack where mortar joints are not used. Meets the requirements of ASTM C 1714, ASTM C270, ANSI 118.4, and ACI 530 Shear Bond Standards.


ProSpec® PVT Masonry Veneer Mortar HB

ProSpec® PVT Masonry Veneer Mortar HB (High-Bond) (BOM #120462) is a high-performance, non-sag, fiber-reinforced, polymer-modified bonding mortar for installing real or manufactured masonry veneer units. Our Pro Veneer Technology (PVT) is a blend of cementitious materials, oven-dried masonry sand, and special performance admixtures to create a professional strength mortar. This high-yield mortar allows for the same coverage as a traditional 50 lb. bag in a lighter-weight 40 lb. size. Meets or exceeds the requirements of ANSI A118.4, A118.11, A118.15 and ASTM C270.


ProSpec® Rapid Patch® Commercial DOT Repair

ProSpec® Rapid Patch® Commercial DOT Repair (BOM #100689) is a rapid-setting, high-strength, polymer-modified, one-component hydraulic cement mortar designed for concrete repair and overlay applications requiring high durability. Meets or exceeds ASTM C928-R3 Standard Specification for Packaged, Dry, Very Rapid, Hardening Cementitious Materials for Concrete Repair. Resistant to salts, grease, oil, and other chemicals often found in the transportation environment. ProSpec Rapid Patch Commercial DOT Repair is approved by MNDOT for "Rapid Hardening Materials for Repairs".


ProSpec® Rapid Patch® Horizontal Repair

ProSpec® Rapid Patch® Horizontal Repair (BOM #126173) is a high-strength, fast-setting, low shrinkage patching material for commercial and industrial concrete horizontal surfaces, as well as concrete pavements and highway applications. Approved by MNDOT under Rapid Hardening Materials for Repairs.


ProSpec® Rapid Patch® Vertical Repair

ProSpec® Rapid Patch® Vertical Repair (BOM #126171) is a non-slumping, high-strength, fast-setting, non-shrink, patching material for commercial and industrial vertical and overhead holes in concrete or masonry. Can be shaved or molded to required shapes. Initial set-time of 15 minutes. Maximum application thickness of 1-1/2 in. (38 mm) per layer.


ProSpec® Refractory Mortar

ProSpec® Refractory Mortar is a specially-engineered blend of specific cements and aggregates giving the mortar unique heat-resistance and thermal characteristics for use in high-temperature applications such as inside fire pit rings, setting chimney clay flue liners, parging a smoke chimney chamber, and setting fire bricks. Passes ASTM C 199 for mortar temperature limits to 2,550°F for a minimum of 6 hours. Available in 50 lb. bags (BOM #120924) and 10 lb. pails (BOM #120913).


ProSpec® Restoration Cleaner

ProSpec® Restoration Cleaner is a mild, acidic product that dissolves and removes efflorescence and rust stains from concrete and masonry surfaces. Restoration Cleaner is recommended to be used before applying a sealer to the surface of finished concrete or masonry applications, enabling the sealer to penetrate and seal more effectively. Restoration Cleaner may be used to prepare the surface of concrete or masonry prior to using ProSpec repair products. Available in 5 gal. pails (BOM #120524) and 1 gal. bottles (BOM #120523).


ProSpec® Set Accelerator

ProSpec® Set Accelerator (BOM #120376) is an ASTM C494, Type C, non-chloride, non-corrosive, liquid that improves workability and initial strength while it reduces the hydration time of cement. The product is recommended for use during cooler weather to accelerate set time and reduce the risk of frozen mortar and concrete mixes. It is also recommended for use when early strength gain is desired to speed up projects. ProSpec Set Accelerator provides a reduced curing time, faster set time and increased early strength. The product speeds finishing operations in any weather condition without any corrosive effects.


ProSpec® Siloxane Final Seal

ProSpec® Siloxane Final Seal is an aromatic, solvent-based concrete sealer/water-repellant used to protect cementious surfaces against the damage caused by water pentration. Can be applied to surfaces where a cure and seal coating was previously applied. Available in 1 gal. bottle (BOM #120828), 5 gal. pail (BOM #120827), and 55 gal. drum (BOM #120829).


ProSpec® Siloxane Sealer

ProSpec® Siloxane Sealer is a clear, solvent-based sealer for concrete and cementitious materials. It penetrates and reacts chemically within the capillaires to repel water and protect from the damaging effects of rain, water penetration, chemicals, salt, freeze-thaw cycles, and smog. Provides natural-looking, non-yellowing, invisible protection. Available in 1 gal. bottle (BOM #120826), 5 gal. pail (BOM #120825), and 55 gal. drum.


ProSpec® Stone Veneer Joint Grout

ProSpec® Stone Veneer Joint Grout is a mixture of dry cementitious materials and masonry sand designed to fill joints between real or manufactured stone veneer units. Preblended with air-entrainment admixtures to resist freeze-thaw conditions while increasing flow and durability. Specially formulated for clean installation and flow properties to eliminate clogging when using a grout bag. Mix with water only. "Step 3" of the ProSpec stone veneer installation system used to create decorative exterior or non-load bearing interior veneer walls.  Available in 4 colors to compliment or contrast veneer units: Gray (BOM #120446); Brown (BOM #120449); Tan (BOM #120448); and White (BOM #120447).


ProSpec® Stone Veneer Sealant

ProSpec® Stone Veneer Sealant is a one-component, high-performance, non-priming, gun-grade, polyurethane elastomeric sealant. It requires no mixing and typically requires no priming to bond to many materials, including concrete and masonry.  Available in 4 colors to coordinate with ProSpec Stone Veneer Grout: Gray (BOM #120450); Brown (BOM #120453); Tan (BOM #120452); and White (BOM #120451).


ProSpec® Super Clear Coat

ProSpec® Super Clear Coat is used for curing and sealing exposed aggregate and sealing colored concrete. This aromatic solvent-based coating does not yellow when exposed to the sun’s UV rays and can also be used as a final sealer on burnish block, architectural concrete, brick, slate, paving stone, terrazzo,quarry tile, and cementitious materials. Enhances the colors of the surfaces with a rich ""wet-look"" sheen. Available in 1 gal. bottle (BOM #120831), 5 gal. pail (BOM #120830), and 55 gal. drum (BOM #120832).


ProSpec® Super Clear Coat Matte

ProSpec® Super Clear Coat Matte is used for curing and sealing exposed aggregate and sealing colored concrete. This aromatic, solvent-based sealer does not yellow under the sun's UV rays. It enhances the beauty of colored or stamped conrete and exposed aggregate yet keeps a matte, low gloss finish. Available in 1 gal. bottle (BOM #120834), and 5 gal. pail (BOM #120833).


ProSpec® Super Diamond Glaze

ProSpec® Super Diamond Glaze is a higher viscosity version of Super Clear Coat used for curing and sealing exposed aggregate and sealing colored concrete. Enhaces the beauty and depth of the surface, giving it a rich "wet-look" high gloss while protecting from the damages caused by moisture penetration. Available in 1 gal. bottle (BOM #120836), 5 gal. pail (BOM #120835), and 55 gal. drum (BOM #120837).


ProSpec® Surface Bonding Cement CR

ProSpec® Surface Bonding Cement CR is a versatile fiber-reinforced, Portland cement-based product used to build and restore retaining walls or block walls, patch large vertical holes where non-sagging cement is a must, repair deteriorated stucco, and in the construction of concrete block walls that are dry stacked (without mortar) above the first course. Special fibers control shrinkage, cracking, and sagging on vertical applications and provides additional overall strength when compared with conventional concrete. Available in Gray (BOM #126197) and White (BOM #120881).


ProSpec® Thermaseal® Geothermal Grout

ProSpec® Thermaseal® Geothermal Grout is a a thermally-conductive cementitious grout engineered for application of vertical and horizontal ground source heat pumps and geothermal well fields. Non-toxic and non-shrink with a high solids content and a low-permeability factor making it ideal for ground source heat loops and safe for contact with potable ground water. A blend of thermally-conductive sand with Portland cement for a target thermal conductivity standard of 1.0 BTU/hr-ft-F°. Thermaseal Geothermal Grout also offers low-absorption with a rigid seal to prevent integration of aquifers and is made in two versions, a MN Mix (BOM #104963) and HF (high-flow) (BOM #120699).


ProSpec® Tile Crete® Floor Mud

ProSpec® Tile Crete® Floor Mud is a blend of cementitious materials and oven dried sand developed to produce a water resistant and highly bondable substrate. Gray color is available in fine sand mix (BOM #105136), coarse sand mix (BOM #105154), and 50/50 mix (BOM #105141) Tile Crete is pre-blended and manufactured to optimize consistency from batch-to-batch. Simply add water and mix to create an easy to apply underlayment. Use as a setting bed/underlayment for ceramic, mosaic, quarry, and paver tile over concrete or wood subfloors and countertops. Tile Crete is also the ideal product for forming shower pans and curbs as well as installations requiring a slope to drain. Tile Crete Floor Mud also offers specialty mixes including a blend for exterior floor underlayments (BOM #105165), fast-setting floor underlayments (BOM #105178), fast-setting with fine sand (BOM #110513), and white cement with fine sand (BOM #100557). Contact your sales rep for more information.


ProSpec® Vertical Concrete Surface Finisher

ProSpec® Vertical Concrete Surface Finisher is a superior cementitious waterproofing coating for concrete and masonry. It provides a protective and waterproof surface while eliminating the rubbing process. Spray or brush applied, available in light gray (BOM 120765) or white (BOM 120764). For added performance, durability, and improved bonding, Vertical Concrete Surface Finisher is designed to be mixed with ProSpec Mighty Bond liquid additive. Vertical Concrete Surface Finisher when mixed with Mighty Bond is approved by MNDOT under Special Surface Finish System.


ProSpec® Vinyl Concrete Patch

ProSpec® Vinyl Concrete Patch (BOM #120681)a polymer-modified, Portland cement-based patching compound used to repair minor surface imperfections in concrete. Suitable for interior and exterior applications from feather-edge to 2 in. (51 mm) thick per lift. Typically supports foot traffic in 8-12 hours, wheeled traffic in 48 hours.


ProSpec® Waterproofing & Crack Isolation Membrane

ProSpec® Waterproofing & Crack Isolation Membrane is an advanced latex polymer-based technology used as a professional grade waterproofing underlayment membrane or as part of a crack isolation system. Salmon color when applied, dries to dark orange. Available in 1 gallon pail (BOM #120675), 3.5 gallon pail (BOM #127630), and 5 gallon (BOM #120676).


 

 

SHARE