DIY Repair


Akona® Concrete Repair

Akona® Commercial Grade Concrete Repair (BOM #103173) is a flexible, quick-drying, paintable filler and sealant for repairs to vertical and horizontal concrete, masonry, stone, and stucco surfaces. It's gray color and sanded texture is designed to blend in with most standard concrete surfaces.


Akona® Concrete/Masonry Restoration Cleaner

Akona® Concrete/Masonry Restoration Cleaner (BOM #102652) is a mild, acidic product that dissolves and removes efflorescence (white mineral deposits) and rust stains from concrete surfaces, masonry units, pavers, brick, etc. This product is recommended to be used before applying a sealer to the surface of concrete or masonry. This enables the sealer to penetrate and seal more effectively. Use this product before applying Akona Penetrating Paver & Masonry Sealer or Akona Water Based Concrete Sealer. In addition, Akona Surface Concrete Cleaner may be used to prepare the surface of concrete or masonry prior to using Akona Repair Products.


Akona® Epoxy Crack Repair

Akona® Epoxy Crack Repair (BOM #120439) is a two-component, high-strength, 100% solids, epoxy repair product designed for injection into horizontal cracks in structural materials including concrete and bricks for the purpose of bonding and sealing. Special no-mess, self-mixing tube for easier application. Use to fill and bond narrow horizontal cracks up to 1/4" (6 mm) wide x 6" (150 mm) deep. Dries clear to light yellow color.


Akona® Fast-Setting Anchoring Epoxy

Akona® Fast-Setting Anchoring Epoxy (BOM #120438) is a two-component, high-performance, 100% solids, high-modulus, non-sag gel epoxy designed for anchoring bolts, railings, dowels, and rebar steel into concrete and to bond or repair a variety of household and common building materials including concrete, porous tile, and stone. Special no-mess, self-mixing tube for easier application. Non-shrink, resistant to chemicals and solvents, this high-strength, fast-setting epoxy has a gel time in as little as 12-14 minutes; initial cure of 2 hours; and final cure time of 12-16 hours. Use both horizontal and vertical, up to 1/8" (3 mm) annular width and 10" (254 mm) depth. Because it is moisture tolerant, it is ideal for stopping air and water leaks. Gray in color.


Akona® Heavy-Duty Waterproofing Base Coat

Akona® Heavy-Duty Waterproofing Base Coat (BOM #102624) is a Portland cement-based, waterproof coating for use over concrete, block, brick or stucco surfaces. Use for interior or exterior coating of foundation, basement or retaining walls below or above grade. When applied over non-uniform areas, this product provides a smooth or textured surface that can be left as a finished decorative coating. In addition, this product can serve as a base coat for paint or similar faux finishes.


Akona® Instant Anchoring Cement

Akona® Instant Anchoring Cement (BOM #102645) is a quick-setting, anchoring cement compound used for setting poles, railings, bolts and fixtures in concrete or masonry. Suitable for interior or exterior use, this product expands as it hardens to set securely and lock in place for strong support. Average set time = 20 minutes


Akona® Instant Patching Cement

Akona® Instant Patching Cement (BOM #102632) is a high-performance cement used for filling wide cracks and other concrete repair needs. It sets rock hard in just 90 minutes. Akona Instant Patching Cement self-bonds to all properly-prepared concrete surfaces and develops twice the strength of ordinary concrete.


Akona® Instant Water Stop

Akona® Instant Water Stop is a quick-setting, hydraulic cement compound used primarily as a water stop or hole filler on concrete or masonry materials. It is formulated to expand when set and locks into place to block flowing water within 3 to 5 minutes. Instant Water Stop bonds to wet walls and is ideal for patching cracks and leaks in swimming pools and is available in 10 lb. bags (BOM #102635) and 25 lb. bags (BOM #102636)


Akona® Mortar Repair

Akona® Commercial Grade Mortar Repair (BOM #103174) is designed for tuck-pointing, repairing, and sealing mortar joints and cracks in masonry units such as stone, brick and block walls. The product is gray in color and designed to blend in with the texture of surrounding mortar. Our durable, pre-mixed Mortar Repair is a sanded, acrylic formulation that dries quickly, is paintable, and provides superior adhesion to masonry.


Akona® Polymer-Modified Concrete Resurfacer

Akona® Polymer-Modified Concrete Resurfacer is a special, acrylic, polymer-modified cement used to resurface spalled and/or damaged interior and exterior concrete surfaces such as steps, patios, garage floors, and sidewalks. Akona Concrete Resurfacer bonds and dries to a concrete gray color. This high-strength product has superior bond and is trowelable to from 1/4 in. down to 1/8 in. (6 to 3 mm). It may be trowel or broom finished, and is available in a 25 lb. bag (BOM #102642).


Akona® Pourable Gray Concrete Crack Filler

Akona® Gray Pourable Concrete Crack Filler is a ready-mixed, easy-to-apply, pourable material for filling cracks up to ¼" deep x ¼" wide. Gray in color to blend with concrete surfaces and flexible to conform to movements of active cracks, Concrete Crack Filler is ideal for horizontal concrete surface such as driveways, sidewalks, patios and garage floors. Available in 1 gal. bottles (BOM #102639) and 1 qt. bottles (BOM #102638). For larger cracks and holes, use Akona Vinyl Cement Patch.


Akona® Premium Concrete Repair

Akona® Premium Concrete Repair (BOM #102637) is a quick-setting repair product ideally suited for vertical applications. This product combines the superior bonding and abrasion resistance of our polymer system with the strength of Portland cement. The result is a patch that is strong and durable. Quickly and easily fill chips in concrete steps, sidewalks, floors, and more. Also use to fill small holes in concrete or masonry.


Akona® Pre-Mixed Concrete & Stucco Patch

Akona® Pre-Mixed Concrete & Stucco Patch (BOM #103962) is a water-based formula intended to patch minor cracks, holes, and surface defects in concrete or stucco. Product may also be used for residential repairs of masonry walls and re-applying small broken pieces of concrete or tuck pointing brick mortar joints. Pre-Mixed Concrete & Stucco Patch offers superior adhesion and may be used for vertical or horizontal patches. 


Akona® Rapid Patch® Concrete Refinisher

Akona® Rapid Patch® Concrete Refinisher (BOM #103145) is a heavy-duty, fast-setting patching material for concrete tilt-up panels, pre-cast concrete, concrete block, concrete pipe, and other concrete or masonry surfaces. This product is suitable for interior or exterior use. Just add water to create a workable, easy-to-apply mixture with excellent bonding characteristics. This product may be trowel applied over existing concrete surfaces from a feather-edge to 2" thickness to finish the appearance of concrete surfaces. It can be shaved or sanded to required shape. Its fast-setting characteristics made it ideal for vertical, horizontal, and overhead applications and when down time is critical.


Akona® Rapid Patch® Concrete Surface Repair

Akona® Rapid Patch® Concrete Surface Repair (BOM# 102896) is a high-strength, fast-setting, low-shrinkage patching material for commercial and industrial horizontal concrete surfaces. Concrete Surface Repair can also be used for concrete pavements, highway applications, concrete levelling and underlayments. Meets ASTM C928-R2. MN DOT approved under "Rapid Hardening Materials for Repairs".


Akona® Vinyl Cement Patch

Akona® Vinyl Cement Patch is ideally suited for repairs to damaged concrete steps, sidewalks, driveways, patios, curbs, walls and floors. This product contains unique polymers that give it twice the strength and three times the adhesion of conventional concrete. Just add water and mix for an easy-to-use product which can be troweled to a feather edge on interior and exterior concrete applications. For resurfacing large areas, use Akona Polymer-Modified Concrete Resurfacer.


Akonaflex® Pro Self-Leveling Expansion Joint Filler

Akonaflex™ Pro Self-Leveling Expansion Joint Filler is a superior-grade, one-component, urethane sealant and filler to be used in concrete joints as well as a wide variety of substrates. Its self-leveling characteristics provide a smooth finish which makes it ideal for filling cracks or gaps on horizontal surfaces such as concrete driveways, sidewalks, above ground foundations, patios, concrete steps, garage floors, and other concrete surfaces. Akonaflex Pro fills expansion joints up to 1½" W x 1"D. Can be exposed to water after only 2 hours under normal conditions without washing out. It will reach full cure after 24 hours. Does not crack or shrink and thus acts as an excellent waterproof seal. Available in 2 convenient sizes: 10 oz. tubes (BOM #104560); and 29 oz. tubes (BOM #120440).


Akonaflex® Self-Leveling Concrete Repair

Akonaflex™ Self-Leveling Concrete Repair is a one-component, construction-grade, polyurethane, moisture-cure sealant designed to meet the flexibility requirements of dynamically moving joints. Self-leveling to result in a smooth, gray finish which is foot-traffic ready after 3 days and will reach full cure in 1 week. Fills and seals horizontal joints up to 1"W x ½"D on concrete slabs, driveways, sidewalks, decks, pitch pans, pavers, garage floors, industrial floors and other concrete surfaces. Its premium-grade components give you a strong, durable, flexible, waterproof seal and leaves a finish that can be painted once cured with a latex paint. Complies with ASTM C920, Federal Specification TTS-00230C, and is VOC compliant. Available in 2 convenient sizes: 10 oz. tubes (BOM #104562); and 29 oz. tubes (BOM #120456).


Akonakote® Pourable Concrete Patch

Akonakote™ Pourable Concrete Patch (#104626) is a flowable, squeegee-grade, polymer-modified patching and resurfacing mix. This flowable, easy-to-use formula can be applied standing up to corrects defects on concrete surfaces prior to applying new flooring materials or coatings. Additionally, Pourable Concrete Patch can be used as a wearable surface in some applications. For deeper repairs over ½" in concrete floors, it is advisable to use Akona Instant Patching Cement prior to using this product.


Akonaseal® Polyurethane Masonry/Joint Sealant

Akonaseal™ Polyurethane Masonry/Joint Sealant (BOM #104561) has an updated package and name (previously called Polyurethane Construction Textured Sealant). A premium-grade, multi-purpose, moisture-cure sealant, designed to meet the flexibility requirements of dynamically moving cracks and joints, this texturized, gray mortar-colored sealant is ideally suited for vertical concrete, stucco or masonry applications with a maximum joint of 1"W x ½"D and can be painted with a latex paint when cured. Complies with ASTM C920, Federal Specification TTS-00230C, and is VOC compliant.


QUIKRETE® FastSet™ Repair Mortar

QUIKRETE® FastSet Repair Mortar (BOM #109719) is specifically formulated to make structural repairs to any concrete, masonry or stucco surface. This low-sag formula has a 20-30 minute working time which allows for sculpting of the material during placement and makes it ideal for vertical and overhead repairs. Just add water, mix, and use to repair concrete, masonry, or stucco surfaces. Exceeds ASTM C 928 R-2. Compressive strength ASTM C109 modified: 3 hours=2,000 psi, 24 hours = 4,000 psi, 7 days = 5,000 psi, and 28 days = 6,000 psi.


QUIKRETE® Sand Mix

QUIKRETE® Sand/Topping Mix (BOM #101231) consists of a uniformly-blended mixture of Portland cement, commercial-grade sands and other approved ingredients. Just add water and mix to repair or top damaged concrete surfaces less than 2" thick.


QUIKRETE® Vinyl Concrete Patcher

QUIKRETE® Vinyl Concrete Patcher is a multi-purpose concrete repair material with strong adhesive properties which trowels to a feather edge of 1/16" (1.6 mm) and is made of a special blend of exterior-grade vinyl resin, fine sand, and Portland cement. Just add water. Available in 40 lb. bags (BOM #100472), 20 lb. pails (BOM #100131), and 10 lb. pails (BOM #109334).


SAKRETE® Concrete Crack Filler

SAKRETE® Concrete Crack Filler (BOM #120026) is a flowable, polymer-based crack filler for concrete. This repair material is designed to fill and seal cracks in concrete up to 1/4 in. wide and 1/4 in. deep.


SAKRETE® Flo-Coat Concrete Resurfacer

SAKRETE® Flo-Coat Concrete Resurfacer (BOM #120034) is a polymer-modified sand and cement mix for resurfacing concrete from 1/8 inch to 1/4 inch depth. Can be applied in a flowable consistency using a squeegee or in a stiffer consistency using a trowel.


SAKRETE® Pre-Mixed Concrete Patch

SAKRETE® Pre-Mixed Concrete Patch (BOM #120547) is used for filling and sealing cracks in concrete up to 1 inch wide. Smooth minor surface defects and holes.


SAKRETE® Sand Mix

SAKRETE® Sand Mix (BOM #100397) is a quality mixture of sand and cement designed to be used as a topping mix to rejuvenate damaged concrete surfaces or as a bedding mix and joint grout for flagstone, slate, and brick walkways. Sand Mix can be applied in layers ranging from ½ to 2 inches thick and exceeds the strength requirements of ASTM C 387. Just add water, mix, and use.


SAKRETE® Top 'n Bond Concrete Patcher

SAKRETE® Top 'n Bond Concrete Patcher (BOM #120031 = 10 lb. / #120032 = 50 lb.) is a polymer-modified sand-cement repair mortar for resurfacing, patching, and general concrete repairs from ½ inch to featheredge. Requires only the addition of water.


TECH-MIX® Concrete Mix

TECH-MIX® Concrete Mix (BOM #104879) is a high strength pre-blended Portland cement mixture for pouring concrete 2 inches thick or greater. Used for general building and repairing steps, slabs, walks, and floors.


Akona® Rapid Patch® Concrete Refinisher Pouch

Akona® Rapid Patch® Concrete Refinisher (BOM #104563) is a fast-setting patching material for concrete pavement, curbs, steps, block and all other interior or exterior concrete surfaces. The convenient zip-pouch package is designed with the do-it-yourselfer in mind for smaller repair projects. Just add water and mix in the bag to create a workable mixture with excellent bonding characteristics. Trowel apply over existing concrete surfaces from a feather edge to 2" thickness to fix minor blemishes. It can be shaved or molded to required shape. Use all the product at once, or take some out and save the rest for another project. And when you're done, our disposable, mix-in-the-bag package makes clean-up a breeze.


 

 

SHARE